A Chrysler Transponder Key once programmed into a one car cannot be programmed to work any other car.
The unlock keys sold out there use at your own risk
The transponder code identification is learned by the Sentry Key Immobilizer Module during programming. The Sentry Key Immobilizer Module sends the "Secret Code" to the transponder key and is retained by the transponder key during programming. After programming of the transponder key identification to the Sentry Key Immobilizer Module and the Secret Code is exchanged, the Sentry Key Immobilizer Module will ask for the transponder identification and the Secret Code every time the key is turned to ON or START.
No Emergency "Start" procedures for Chrysler vehicles.
The unlock keys sold out there use at your own risk
The transponder code identification is learned by the Sentry Key Immobilizer Module during programming. The Sentry Key Immobilizer Module sends the "Secret Code" to the transponder key and is retained by the transponder key during programming. After programming of the transponder key identification to the Sentry Key Immobilizer Module and the Secret Code is exchanged, the Sentry Key Immobilizer Module will ask for the transponder identification and the Secret Code every time the key is turned to ON or START.
No Emergency "Start" procedures for Chrysler vehicles.
Chrysler Key Operation and Programming
300 2005 - 2008
300C 2005 - 2007
300C 2005 - 2007
Remote alarm / central locking
System Operation
- Pressing key LOCK button activates alarm and central locking.
- Pressing key UNLOCK button once deactivates alarm system and unlocks driver's door.
- Pressing key UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors and trunk.
- Pressing trunk lid button twice opens trunk lid.
- System will automatically lock all doors when vehicle is driven above 15 mph.
- Additional functions can be set to respond to the transmitter.
When
- Key transmitter added or replaced.
- Key transmitter is programmed during immobilizer programming procedure.
Immobilizer
System Operation
- Switch ignition ON.
- Immobilizer warning lamp illuminates for approximately 3 seconds.
When
- Keys added or replaced.
NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using diagnostic equipment.
- Insert first programmed key into ignition switch.
- Switch ignition ON for at least 3 seconds but no longer than 15 seconds.
- Turn ignition OFF and remove key.
- Withing 15 seconds insert second programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.
- Turn ignition OFF and remove second programmed key.
- Within 60 seconds insert non programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.
- Switch ignition OFF.
- Remove Key.
Repeat procedure for additional key transmitters if required.
Example key:
 |
| Chrysler Keys with Remote |
Remote alarm / central locking
System Operation
- System will automatically lock all doors when vehicle is driven above 15 mph.
- Pressing remote transmitter UNLOCK button once deactivates alarm system and unlocks driver's door only.
- Pressing remote transmitter UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors.
- Alarm / Central locking functions can be altered using remote transmitter.
Programming
When
- Remote transmitter added or replaced.
How:
NOTE: One programmed Remote transmitters must be available for the following procedure to operate.
- Obtain all remote transmitters.
NOTE: Any existing remote transmitters not used during programming will become inoperative.
- Switch ignition ON.
Using a programmed remote transmitter proceed as follows.
- Press and hold remote transmitter UNLOCK button.
- After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press remote transmitter PANIC button for at least 1 second and release both buttons.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote remote transmitter)
- Press any button of each remote transmitter to be programmed.
- Ensure acoustic signal is emitted after each remote transmitter operation.
- Programming must be completed within 30 seconds.
- Switch ignition OFF or wait 32 seconds to exit programming mode.
Replacement remote transmitters can also be programmed using diagnostic equipment.
Immobilizer
System Operation
- System arms after switching ignition OFF.
- Switch ignition ON.
- Immobilizer warning lamp illuminates for approximately 3 seconds.
When
- Keys added or replaced.
NOTE: Two programmed key transmitters must be available for the following procedure to operate.
- Obtain all keys.
- Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFF position and remove key.
NOTE: First and second programmed key operations MUST be performed within 15 seconds.
- Insert second programmed key and switch ignition ON.
- Wait approximately 10 seconds.
- Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted.
- Switch ignition OFF and remove key.
- Within 50 seconds, insert new key and switch ignition ON.
- Wait approximately 10 seconds.
- Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 seconds indicating programming completed.
Replacement keys can also be programmed using diagnostic equipment.
Remote Control Example:
 |
| Chrysler Remote |
Automotive and Commercial Locksmith
6105 Johnson Street
Hollywood, FL 33024
Phone: 1.954.347.9566
Website: AutomotiveAndCommercialLocksmith.com
No comments:
Post a Comment